คุณสมบัติทางเทคนิค | UPS specification

Category: Line Interactive Pure Sine Wave
Model Name: Claire 2000

Model Number: CLAIRE 2000

Download Brochure
Check Alarm Code

Features

- Line Interactive with Stabilizer Design

- 100% Digitized Microprocessor Controlled

- Pure Sine Wave Output

- Automatic Voltage Reguration (+/-20%)

- Two in one design: Tower & Rack 19" case

- AC Start (Power On UPS w/o battery)

- DC Start (Power On UPS w/o line input utility)

- Short Circuit, Overload & Surge Protection

- USB port as standard

- Free of charge "WinPower" monitoring & controll S/W via LAN/WAN

- SNMP adaptor with "UPSnodeManger" via SNMP protocal

- MIB II standard for SNMP node management S/W

- Hot Swappable Battery

- Extended Backup Time

- Dual Modular Redundant (Option)

- CE Declaration of Conformity

Product Descriptions

This series is a compact and fully pure sinewave line interactive UPS, and it designs for critical application and environment, such as desktops, servers, workstations, and other networking equipments. This model is available in the output ratings of 750, 1000, 1500, 2000, and 3000VA. This series protects your sensitive electronic equipments against power problems including power sags, spike, brownouts, line noise, and blackouts. This series designs from two-in-one form factor; it can be placed either in Rack 2U or Tower. The UPS case for 750 ~ 2000VA is made of plastic as well as 3000VA is made of metal. This series is powered from the AC mains and supply AC outputs via receptacles on the rear panel.SmartPower "Your Smart Choice of UPS".
*คลิกดูเทคนิค Line interactive pure sine wave

Type	Items	Specification
Capacity	Capacity	2000VA/1200W
Input	Voltage Range	220 +/- 20% VAC
	Frequency Range	50 +/- 10% Hz
	Phase	Single Phase with Ground
	Generator Input	Support
Output	Voltage Range	220 +/- 10% VAC
	Voltage Range (Batt.Mode)	220 +/- 5% RMS for entire battery voltage range
	Frequency Range	50 +/- 0.1% Hz
	Output Wave form	Pure Sine Wave
	Outlet	NEMA x 6
	Redundancy (Option)	Dual Modular Redundant (DMR)
Overload Rating	Line Mode	110% shutdown after 3 minute; 150% shutdown after 10 cycles.
Battery	Battery type	12V/7A (Sealed Lead-Acid Maintenance Free with suspended electrolyte) or on requested
	Number of Battery	4 pcs. or on requested
	Backup time (depends on computer load)	15-30 minutes
	Battery hot swap	YES
	Battery Protection	Battery Overcharges/Battery deep discharge/Auto self test/Fan failure protection
	Recharge Time	3 hrs to 90% after discharge
Transfer Time	Transfer Time	2 ms.
Indicator	AC mode	Line LED lighting
	Backup mode	Battery LED flashing every 4 sec.
	PCB fails	Power module of UPS fails: LED lighting
	Load Level	4 segment LED bar
	Battery Level	4 segment LED bar
	UPS fault	Fault LED lighting
	Overload	Overload LED lighting
	Low Battery	Battery LED flashing every second
	Bad Battery	Bad Battery lighting
	Operating mode	Normal LED, Generator LED and Wide Range LED
	Voltage range	220 V.LED, 230 V.LED and 240 V.LED
Audible Alarm	Battery Mode	Sounding every 4 seconds
	Low Battery	Sounding every second
	Fault	Continuously Sounding
	Overload	Sounding every second
	Bad Battery	Sounding every second
Dimension	Tower Case (WxHxD)mm	217x86.5x413.5
	Battery Case (WxHxD) mm	217x86.5x413.5
Weight	Tower Case (kgs)	6.5
	Battery Case (kgs)	12
Environment	Operation Environment	0-40 C
	Relative Humidity	0-95% (Non-Condensing)
	Noise Level	<45dB @ 1 Meter
Interface	Smart RS-232 / USB	S/W supports Windows Family, Linux, Sun Solaris, IBM AIX, Compaq True64, SGI IRIX, FreeBSD, HP-UX and MAC
	External Slot (Option)	External Type of SNMP
	Dry-Contact	YES
	EPO	YES
International Standard	CE	Low Voltage Directive(Safety): EN62040-1-1, EMC Directive: EN50091-2, EN61000-3-2, EN61000-3-3, EN55022